- Ccna 1 chapter 3 pdf
- CCNA 3 (v5.0.3 + v6.0) Chapter 1 Exam Answers 2019 – 100% Full
- ITN CCNA 1 v6.0 Chapter 1 Exam Answers 2018 2019
- CCNA 1 Chapter 3
- Chapter 11: Managing a Secure Network
- NETACAD Chapter 3 v5.0 Network Protocols and Communications Part 1
- CCNA 1 v6.0 Introduction to Network
- CCNA1 v6.0 (latest Update August 2017)
- CCNA 1 (v5.1 + v6.0) Chapter 3 Exam Answers 2019 – 100% Full
We will update answers for you in the shortest time. Thank you! We truly value your contribution to the website. All modern enterprise networks are expected to support critical applications, converged network traffic, diverse business needs, and provide centralized administrative control. Users expect enterprise networks to be up Support for limited growth is not a usual network design criterion.
Which type of information is displayed by the show ip protocols command that is issued from a router command prompt? The show ip protocols command displays information about the routing protocols that are configured, the networks the router is advertising, and the default administrative distance. The show ip interfaces command displays interface information, including protocol status, the IP address, whether a helper address is configured, and whether an ACL is enabled on the interface.
The show protocols command displays information about the routed protocol that is enabled and the protocol status of interfaces.
Which action should be taken when planning for redundancy on a hierarchical network design? One method of implementing redundancy is path redundancy, installing alternate physical paths for data to traverse the network.
Ccna 1 chapter 3 pdf
Redundant links in a switched network supports high availability and can be used for load balancing, reducing congestion on the network. In the Cisco Enterprise Architecture, which two functional parts of the network are combined to form a collapsed core design?
What are two ways to access a Cisco switch for out-of-band management? Refer to the exhibit.
CCNA 3 (v5.0.3 + v6.0) Chapter 1 Exam Answers 2019 – 100% Full
Which devices exist in the failure domain when switch S3 loses power? A failure domain is the area of a network that is impacted when a critical device such as switch S3 has a failure or experiences problems. As the network administrator you have been asked to implement EtherChannel on the corporate network.
What does this configuration consist of? Which design feature will limit the size of a failure domain in an enterprise network? In order to best limit the of a failure domain, routers or multilayer switches can be deployed in pairs.
ITN CCNA 1 v6.0 Chapter 1 Exam Answers 2018 2019
The failure of a single device should not cause the network to go down. Installing redundant power supplies may protect a single device from a power failure, but if that device suffers from another type of problem, a redundant device would have been a better solution. Purchasing enterprise equipment that handles large flows of traffic will not provide extra reliability in times of an outage.
If a collapsed core design is used, the core and distribution are collapsed into a single device, increasing the chance of a devastating outage. A network administrator is planning redundant devices and cabling in a switched network to support high availability.
Which benefit will implementing the Spanning Tree Protocol provide to this design? With the implementation of redundant devices and links, redundant paths will exist in the network. STP is not required to combine multiple physical interfaces into a single EtherChannel interface.
STP does not provide faster convergence or an expanded network that uses wired or wireless connectivity. What are two benefits of extending access layer connectivity to users through a wireless medium?
CCNA 1 Chapter 3
Wireless connectivity at the access layer provides increased flexibility, reduced costs, and the ability to grow and adapt to changing business requirements. Utilizing wireless routers and access points can provide an increase in the number of central points of failure.
Wireless routers and access points will not provide an increase in bandwidth availability. Which two features of enterprise class equipment assists an enterprise network in maintaining Enterprise class equipment is designed with features such as redundant power supplies and failover capabilities. A failure domain is an area of a network that is impacted when a critical device fails.
A collapsed core is a two-tier hierarchical design where the core and distribution layers are collapsed into a single layer. This reduces cost and complexity but does not provide redundancy and uptime.
A network technician needs to connect a PC to a Cisco network device for initial configuration. What is required to perform this device configuration? Because the device needs to be initially configured, a network connection is unavailable yet on this device, hence the need for an out-of-band management method.
A configuration that uses out-of-band management requires a direct connection to a console or AUX port, and a terminal emulation client. What network design would contain the scope of disruptions on a network should a failure occur? One way to contain the impact of a failure on the network is to implement redundancy. One way this is accomplished is by deploying redundant distribution layer switches and dividing the access layer switch connections between the redundant distribution layer switches.
This creates what is called a switch block. Failures in a switch block are contained to that block and do not bring down the whole network. What are three access layer switch features that are considered when designing a network? Choose three. The port density of a switch the number of ports available on a single switch , forwarding rate how much data the switch can process per second , and Power over Ethernet the ability of the switch to deliver power to a device over the existing Ethernet cabling are access layer switch features to be considered when designing a network.
Failover capability, speed of convergence, and broadcast traffic containment are distribution layer features. Routers connect multiple networks in an organization to provide interconnections among them.
They perform the task by using the network portion of the destination IP address to determine the best path to send packets to their destination. What capability is provided by the use of application-specific integrated circuits in Cisco multilayer switches? Application-specific integrated circuits ASICs increase the forwarding speed of a switch by allowing packets to bypass the CPU for processing.
The Cisco Meraki cloud-managed access switches enable virtual stacking of switches. They monitor and configure thousands of switch ports over the web, without the intervention of onsite IT staff. A network engineer is reviewing a network design that uses a fixed configuration enterprise router that supports both LAN and WAN connections.
Chapter 11: Managing a Secure Network
However, the engineer realizes that the router does not have enough interfaces to support growth and network expansion. Which type of device should be used as a replacement? Modular routers provide multiple slots that allow a network designer to change or increase the interfaces that exist on the router. A Layer 3 switch may increase the number of ports available on a router, but will not provide WAN connectivity.
The PoE capability of a device is not related to the number of ports it has. Using another fixed configuration router will not provide the flexibility to adapt to future growth that using a modular router will provide. In which situation would a network administrator install a Cisco Nexus Series or Cisco Catalyst Series switch to promote infrastructure scalability?
Cisco Nexus Series switches are employed on data centers to promote infrastructure scalability, operational continuity, and transport flexibility. They also provide secure multitenant services by adding virtualization intelligence technology to the data center network.
NETACAD Chapter 3 v5.0 Network Protocols and Communications Part 1
They are commonly used as access layer switches and they are fixed configuration switches. Which command was issued on a Cisco switch that resulted in the exhibited output? The show port-security address command displays all secure MAC addresses configured on all switch interfaces.
The show vlan summary command displays the count of all configured VLANs. In-band device management is used to monitor and make configuration changes to a network device over a network connection. Configuration using in-band management requires at least one network interface on the device to be connected and to be operational, and it requires the use of Telnet, SSH, or HTTP to access the device.
Which two requirements must always be met to use in-band management to configure a network device? Direct connections to the console and auxiliary ports allow for out-of-band management.
CCNA 1 v6.0 Introduction to Network
Terminal emulation software is not always required because in-band management can be performed using a browser. The version number and release number refer to the overall device operating system.
The platform refers to the specific model of a device. The feature set determines what a particular device is capable of. Immediately after a router completes its boot sequence, the network administrator wants to check the routers configuration.
From privileged EXEC mode, which of the following commands can the administrator use for this purpose? The show running-config command can be used to display the currently active configuration that is stored in RAM.
CCNA1 v6.0 (latest Update August 2017)
The show flash command displays the files not file content stored in the flash memory. Question as presented: Match the purpose to the related configuration item. Not all options are used. What is the function of PoE pass-through? Answers is: d.
CCNA 1 (v5.1 + v6.0) Chapter 3 Exam Answers 2019 – 100% Full
Ans is A Moduler Router. Need an answer for the above question. They prevent Layer 2 loops by disabling redundant links between switches. They provide power to devices such as IP phones and wireless access points through Ethernet ports. CCNA 3 v5. Related Articles. This comment form is under antispam protection. Most reacted comment.
Hottest comment thread.