- Step 1: Prepare the location
- Hp 3050 deskjet user manual
- HP Deskjet 3000 Printer series - J310
- Reset Hp deskjet 3050 to default factory setting
- HP Deskjet 3050 All-in-One Printer - J610a Manuals
- HP DESKJET 3050 User Manual
- HP Deskjet 1050 User Manual
- HP Deskjet 3050 All-in-One Printer - J610a
- Software and drivers for
Reproduction, adaptation or translation without prior written permission is prohibited, except as allowed under the copyright laws. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services.
Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy.
Step 1: Prepare the location
If this equipment is not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:.
Connect equipment to an outlet on a circuit different from that to which the receiver is located.
Hp 3050 deskjet user manual
Any changes or modifications to the printer that are not expressly approved by HP could void the user's authority to operate this equipment. This equipment complies with FCC rules, Part On the back of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number REN for this equipment. If requested, this information must be provided to the telephone company.
The REN is used to determine the quantity of devices which may be connected to the telephone line. Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call.
In most, but not all, areas, the sum of the RENs should not exceed five 5. To be certain of the number of devices that may be connected to the line, as determined by the total RENs, contact the telephone company to determine the maximum REN for the calling area.
An FCC-compliant telephone cord and modular plug is provided with this equipment.
This equipment is designed to be connected to the telephone network or premises wiring using a compatible modular jack which is Part 68 compliant. This equipment cannot be used on telephone company-provided coin service. Connection to Party Line Service is subject to state tariffs. If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will notify the customer as soon as possible.
Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment.
HP Deskjet 3000 Printer series - J310
If this happens, the telephone company will provide advance notice in order for you to make the necessary modifications in order to maintain uninterrupted service. If trouble is experienced with this equipment, please see the numbers in the front of this manual for repair and or warranty information. If the trouble is causing harm to the telephone network, the telephone company may request you remove the equipment from the network until the problem is resolved.
Reset Hp deskjet 3050 to default factory setting
The following repairs can be done by the customer: Replace any original equipment that came with the device. This includes the print cartridge, the supports for trays and bins, the power cord, and the telephone cord.
It is recommended that the customer install an AC surge arrestor in the AC outlet to which this device is connected. This is to avoid damage to the equipment caused by local lightning strikes and other electrical surges. All other devices mentioned herein may be trademarks of their respective companies.
HP Deskjet 3050 All-in-One Printer - J610a Manuals
Step 1: Prepare the location Step 2: Regulate the environment Step 3: Verify the package contents Step 4: Locate the all-in-one parts Step 5: Install the control-panel overlay if not already installed Step 6: Install the media tray Step 7: Install the output bin support Step 8: Install the automatic document feeder ADF input tray Step 9: Install the ADF output support Step Install the print cartridge Step Connect the power cord Step Connect a printer cable to the all-in-one Step Connect to a telephone line Step Turn on the all-in-one Step Set the control-panel display language and location if necessary Step Test the hardware setup by printing a configuration report Step Test the copier by using the automatic document feeder ADF Step Complete the hardware setup Step Connect to a Windows computer Windows only Step Fax setup Step Test the software installation Step Register the all-in-one Step Program the Scan To button Windows only Step Support information Tips for using the all-in-one Preventing streaks and spots on scans and copies Clearing print jams Place the all-in-one on a sturdy, level surface in a well-ventilated area.
Make sure that the air vents are not blocked and all doors can open freely. Do not place the all-in-one in direct sunlight or in an area that has abrupt temperature and humidity changes. The recommended ranges are 15 to Remove the adhesive backing from the overlay.
Align the bottom of the overlay with the bottom of the control panel, and make sure that the holes in the overlay align with the keys on the all-in-one. Press the overlay from the bottom up toward the top until it is completely attached to the all-in-one.
HP DESKJET 3050 User Manual
NOTE Make sure that the overlay is aligned correctly and is not pressing any buttons. The control panel includes the following areas:. Remove any shipping tape from the inside and outside of the tray. Slide the tray in until it fits securely.
HP Deskjet 1050 User Manual
Open the top of the media input tray. Slide out the media guides.
Pull out the long-media support. Place the media in the tray, and then adjust the media guides until they are flush with the media. NOTE Do not fan the media before placing it in the tray. Close the top of the media input tray.
HP Deskjet 3050 All-in-One Printer - J610a
Insert the pin on one side of the support into the hole in the all-in-one. Flex the pin on the other side inward, and insert it into the hole. Align the two tabs on the input tray with the two grooves in the ADF lid.
Slide the tray into the grooves until the tray snaps into place. Press the cartridge-door release to open the print-cartridge door. Remove the print cartridge from its packaging, and then rock the cartridge gently five or six times.
Bend the plastic tab at the end of the cartridge. Pull the tab until all the sealing tape is removed from the cartridge. Hold the print cartridge by the handle and insert it into the all-in-one.
Close the print-cartridge door. Hot water or heat from a dryer sets the toner in the fabric. Because they are not HP products, HP cannot influence their design or control their quality.
Software and drivers for
Connect the power cord to the power connector on the back of the all-in-one. Connect the other end of the power cord to a grounded alternating current AC outlet. NOTE Use only the power cord that came with the all-in-one. NOTE If you are using the all-in-one as a standalone fax machine, go to step If you are using it as a standalone copier, go to step NOTE If you are not using the fax functionality, go to step Connect the included fax cord to the port on the all-in-one that is marked with an "L".
Connect the cord to a telephone jack.